Adaptec ASC39320A-ROHS-KIT Betriebsanweisung Seite 184
- Seite / 206
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
F-1
F
Migrating from HostRAID
to Adaptec Ultra320 SCSI
In this Appendix...
If after installing the HostRAID drivers, you decide to use your
controller as standalone SCSI without RAID functionality, you
must disable HostRAID and install the SCSI drivers. To use
standalone SCSI on your Adaptec SCSI Card, refer to the following
sections of this appendix.
Caution: Adaptec recommends that you back up all of your
data before migrating from HostRAID to Ultra320 SCSI.
Warning: Adaptec recommends that if you want to migrate to
standalone SCSI, you migrate from RAID 1 only. If you try to
migrate from RAID 0, you will loose all of your data. See
Disabling HostRAID Support on page F-3 for more information.
Migrating With Windows 2000 F-2
Migrating With Windows XP F-5
Migrating With Windows NT 4.0 F-8
!
U320 UG.book Page 1 Tuesday, September 23, 2003 1:47 PM
- USER’S GUIDE 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Adaptec Customer Support 3
- SCSISelect 10
- 2003, and XP 11
- OpenServer, and Open Unix 13
- Browser Edition 14
- A Troubleshooting in Windows 14
- Contents 15
- Glossary 16
- Introduction 17
- ■ Adaptec SCSI Card 39320A 18
- Device Drivers 19
- HostRAID Features 20
- Storage Management Software 21
- Operating Systems 22
- System Requirements 23
- Understanding SCSI 24
- SCSI IDs 24
- Terminating the SCSI Bus 25
- Defining RAID 26
- Supported RAID Levels 27
- Using the Adaptec SCSI 28
- Card and SCSI Devices 28
- Using SCSI Devices 29
- Connecting the LED Connector 34
- Adaptec SCSI Card 39320A 35
- Adaptec SCSI Card 29320A 35
- Connecting SCSI Devices 36
- Adaptec SCSI Card 29320ALP 39
- Built-in Terminator on Cable 40
- Terminated Device 40
- Maximum Cable Lengths 41
- SCSI Card with SCSISelect 42
- Configuring the Adaptec 42
- Starting SCSISelect 44
- Using SCSISelect Settings 45
- Options – BBS Systems Only 46
- HostRAID Options 52
- ■ Boot Device Configuration 54
- ■ SCSI Device Configuration 54
- Using SCSI Disk Utilities 57
- Using the SCSISelect Utility 61
- =default) 63
- 39320A at slot 6, 00:0E:00 63
- Creating Arrays 65
- ■ RAID-0 66
- ■ RAID-1 66
- ■ RAID-10 66
- Creating RAID 0 Arrays 67
- Creating RAID 1 Arrays 68
- Creating RAID 10 Arrays 69
- Create Array? 70
- Are you sure? 70
- Deleting Arrays 71
- Adding a Spare Drive 71
- Rebuilding Arrays 72
- Verifying Data Integrity 73
- Bootable Array 75
- Check Point 75
- Installing the HostRAID 76
- Driver for Windows 2000 76
- 2003 is Already Installed 78
- Configuration Notes 80
- Driver for Windows NT 4.0 81
- If Windows NT 4.0 Setup Hangs 84
- Driver for Linux 86
- Installing Red Hat Linux 87
- Installing SuSE Linux 88
- For Windows 2000/2003 90
- Windows NT 100
- Already Installed 102
- Hot-Plug PCI Support 103
- Removing a Host Adapter 104
- Swapping a Host Adapter 105
- Troubleshooting 107
- Error Messages 109
- Installing the SCSI Driver 110
- NetWare 5.1 and 6.x 111
- Installed 112
- Sample Load Commands 115
- Using Removable Media 115
- Using the NetWare Tape Backup 117
- Using a CD with NetWare 118
- Optimizing Performance 118
- Open Unix 123
- Back Up the Kernel 126
- Load the Package 126
- Modify the New System File 127
- Boot the New Kernel 128
- OpenServer 129
- Using Tunable Parameters 130
- Removing the Driver 131
- /reconfigure file by typing: 140
- Command Line Options 141
- Additional Notes 142
- Installing Adaptec Storage 145
- Manager–Browser Edition 145
- Supported Browsers 146
- Autorun 147
- Logging On 152
- Troubleshooting in 154
- Troubleshooting Checklist 155
- General Troubleshooting 156
- Common Error Messages 159
- Windows Error Messages 160
- Driver Error Messages 161
- Using Windows Advanced 164
- Configuration Parameters 164
- Using Windows SCSI Parameters 165
- Creating Driver Floppy 169
- Installation Options 170
- Running Windows 171
- Running OpenServer 172
- Running Linux 173
- Running DOS/NetWare 173
- Migrating From Adaptec 175
- Ultra320 SCSI to HostRAID 175
- Migrating With Windows 2000 176
- Enabling HostRAID Support 177
- Migrating With Windows XP 179
- Migrating With Windows NT 4.0 181
- Migrating from HostRAID 184
- Disabling HostRAID Support 186
- Glossary-2 195
- Glossary-3 196
- Glossary-4 197
- Glossary-5 198
- Glossary-6 199
- Glossary-7 200
- Adaptec, Inc 206
- 691 South Milpitas Boulevard 206
- Milpitas, CA 95035 USA 206
Verwandte Produkte und Handbücher für Schnittstellenkarten / Adapter Adaptec ASC39320A-ROHS-KIT
(14 Seiten)
(30 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.108 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern