Adaptec ICP9085LI Betriebsanweisung Seite 35
- Seite / 113
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 5: Installing the Controller and Disk Drives ● 35
● For SATA RAID controllers, see page 37.
● For SCSI RAID controllers, see page 38.
If you are not installing internal disk drives, close your computer cabinet, reattach the
power cord, then continue with Connecting External Devices on page 38.
Connecting Disk Drives to SAS RAID Controllers
You can connect SAS disk drives, SATA disk drives, or a combination of both to your SAS
RAID controller. There are no jumpers or switches to set before installation.
If you plan to build a bootable array using internal disk drives, ensure you install at least the
minimum number disk drives required to support the RAID level you want. See page 28 for
more information.
Note:
Although you can connect both SAS and SATA disk drives to your SAS controller, ICP
recommends that you not combine SAS and SATA disk drives within the same array or logical
drive. See page 64 for more information.
You have two connection options:
● To connect directly to the controller, see the following section.
● To connect to a backplane, see page 37.
Connecting Directly to the Controller
In a direct-attach connection, SAS or SATA disk drives are connected directly to a SAS card
with SAS cables.The number of direct-attached disk drives is limited to four per internal SAS
connector. (For more information about direct-attach connections, see page 67.)
1 Install your internal SAS or SATA disk drives, following the instructions in your system’s
documentation.
- SAS, SATA, and SCSI 1
- RAID Controllers 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- ICP vortex Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- Using the ICP Flash Utility 10
- Safety Information 10
- Technical Specifications 10
- About This Guide 11
- How to Find More Information 12
- Kit Contents and System 13
- Requirements 13
- Kit Contents 14
- System Requirements 14
- CD drive 15
- About Your RAID Controller 16
- Array-level Features 17
- RAID Controller Battery Model 18
- About the ICP5445AU 19
- About the ICP5085AU 20
- About the ICP9085LI 21
- About the ICP5085BR 22
- About the ICP9047MA 23
- About the ICP9087MA 24
- About the ICP9014RO 25
- About the ICP9024RO 26
- Getting Started 27
- Choosing a RAID Level 28
- Selecting Disk Drives 29
- Selecting Cables 30
- SATA Cables 31
- SCSI Cables 31
- Installation Options 32
- Basic Installation Steps 32
- In this chapter 33
- Before You Begin 34
- Installing the Controller 34
- Devices on page 38 36
- Disk drives on 37
- Controller connected to 37
- Connecting External Devices 38
- Failed Device is faulty On 39
- Other No error Off 39
- Creating a Bootable Array 40
- Setting the Boot Controller 41
- Creating an Array 41
- Making Your Array Bootable 44
- Installing the Driver and an 45
- Operating System 45
- Creating a Driver Disk 46
- Installing with Windows 47
- Installing with Red Hat Linux 47
- Installing with SUSE Linux 48
- Installing with NetWare 48
- Installing with OpenServer 49
- Installing with UnixWare 49
- Installing with FreeBSD 50
- Installing on Windows 53
- Installing on NetWare 53
- Installing on OpenServer 54
- Installing on UnixWare 54
- Installing on Solaris 55
- Installing on FreeBSD 55
- Managing Your Storage Space 56
- About ICP Storage Manager 57
- About the ICP Flash Utility 58
- Which Utility Should I Use? 58
- Solving Problems 59
- Troubleshooting Checklist 60
- Silencing the Alarm 60
- Resetting the Controller 62
- In this appendix 63
- ) Web site at www.scsita.org 63
- What is SAS? 64
- What’s a Phy? 65
- What’s a SAS Port? 66
- What’s a SAS Address? 66
- What’s a SAS Connector? 66
- What do SAS Cables Look Like? 66
- Direct-attach Connections 67
- Backplane Connections 67
- SAS Expander Connections 68
- Understanding RAID 70
- Understanding Drive Segments 71
- Nonredundant Arrays (RAID 0) 71
- RAID 1 Arrays 72
- RAID 1 Enhanced Arrays 72
- RAID 10 Arrays 73
- RAID 5 Arrays 74
- RAID 5EE Arrays 75
- RAID 50 Arrays 76
- RAID 6 Arrays 77
- RAID 60 Arrays 77
- Selecting the Best RAID Level 78
- Creating a New Array 80
- Managing Existing Arrays 81
- Initializing Disk Drives 81
- Rescanning Disk Drives 81
- Secure Erasing Disk Drives 82
- Opening a -Select Utility 82
- Applying Changes and Exiting 82
- General Controller Settings 83
- Option Description 84
- Viewing the Event Log 86
- Running the ACU Using Scripts 89
- About Record Mode 90
- Required 91
- ? Description 91
- HotspareDrives=0:0:0,0:1:0 92
- Type=Volume 92
- Type=RAID1 92
- ACU exits with an error 93
- Keyword Description 94
- ACU Error Codes 95
- Sample Scripts 96
- Running the Menu-based IFU 100
- Running the 101
- Current Requirements 107
- Environmental Specifications 107
- DC Power Requirements 107
- Index ● 109 109
- Index ● 110 110
- Index ● 111 111
- Index ● 112 112
- Konrad-Zuse-Str.9 113
- 74172 Neckarsulm 113
Verwandte Produkte und Handbücher für Peripheriegeräte Adaptec ICP9085LI
(6 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.149 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern