Adaptec Snap Server 700i Series Betriebsanweisung Seite 197
- Seite / 238
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
• Standardize on a single vendor for external hardware components — Not only
will standardization on a single vendor minimize the chance of unforeseen
interoperability failures, it will also simplify troubleshooting procedures.
Notes (1) For a complete list of qualified components, including replacement parts
and installation instructions, see http://www.snapserver.com/support
; (2) To find
an authorized reseller in your area, go to http://www.snapserver.com
and click the
Where to Buy tab.
Identifying the Ethernet Ports
The Snap Server 700i Series have an on-board NIC card with two Ethernet ports
(eth0 and eth1). In addition, the Snap Server 720i has a single-port NIC (eth2) and
the Snap Server 730i and 750i have a dual-port NIC (eth2 and eth3). The illustration
below identifies the location of each of these Ethernet ports.
MGMT
eth0
eth0
eth1
e
t
h2
eth3
- Snap Server 1
- 700i Series 1
- User’s Guide 1
- Contents 7
- About this Guide 13
- Service and Technical Support 15
- Notes and Cautions 16
- Finding More Information 16
- US/Support 17
- Source and Location Content 17
- Planning Your IP SAN 19
- Windows Support 23
- Sample IP SAN Configurations 24
- Basic Configuration #1 25
- Basic Configuration #2 26
- Configuration with Mirroring 27
- GbE SwitchGbE Switch 29
- Net A Net B 29
- Net C Net C Net C 29
- GbE Switch 29
- System Requirements 31
- Installing Adaptec Storage 33
- Click Install 35
- Installing on Linux 36
- 4 Unmount the CD: 38
- Appliance and IP SAN 39
- Before You Begin 40
- Creating RAID Pools 44
- Beginning to Use Your IP SAN 53
- Setting Up VSS/VDS Access 54
- Next Steps 56
- Getting to Know Adaptec 57
- Storage Manager 57
- Navigating the Main Window 58
- The Physical Devices View 61
- The Logical Devices View 62
- The Volumes View 63
- The Snapshots View 63
- Revealing More Information 64
- Protecting Your Data 67
- Deleting a Hot Spare 69
- Mounting a Snapshot Set 72
- Creating Volume Snapshots 75
- Scheduling a Snapshot Job 76
- Creating a Mirrored Volume 80
- Extending a Mirrored Volume 81
- Changing Mirror Priorities 81
- Breaking a Mirrored Volume 83
- Deleting a Mirrored Volume 84
- Specifying Replica Site 84
- Creating Replicas 85
- Updating Replica Set 85
- Aborting a Replica Set Update 86
- Switching Roles 86
- Mounting a Replica Set 86
- Unmounting a Replica Set 86
- Breaking a Replica Set 86
- Scheduling Replica Update 87
- Chapter 7 89
- Opening the Security Manager 94
- Modifying Your iSCSI Storage 97
- Adding an iSCSI Storage Host 98
- Capacity Limitations 99
- Creating and Modifying Pools 100
- Adding Capacity to a Pool 102
- Changing a Pool’s RAID Level 102
- Deleting an Individual Pool 107
- Deleting All Pools 107
- Creating a New Volume 108
- Adding Capacity to a Volume 109
- Deleting a Volume 110
- Creating a New Logical Device 110
- Modifying a Logical Device 111
- Deleting a Logical Device 111
- Appliance 113
- Applying a New Image 117
- Checking the Current Image 118
- Monitoring Jobs in Progress 121
- Opening the Job Manager 122
- Cancelling a Job in Progress 122
- Resuming a Cancelled Job 123
- Undoing a Failed Job 123
- Viewing Status and Activity 124
- Viewing Enclosure Status 125
- Viewing Component Properties 126
- Components 127
- Behavior 130
- SEP MASTER 132
- Sending a Test Message 134
- Modifying Email Settings 135
- Disabling Email Notifications 135
- Sending a Test Trap 137
- Disabling SNMP Traps 137
- The server is offline 138
- 4 Click OK 144
- Updating and Customizing 145
- Adaptec Storage Manager 145
- Viewing Display Group Status 148
- Modifying Display Groups 148
- Solving Problems 149
- Silencing an Alarm 154
- Hot Swapping Disk Drives 156
- Rebuilding Pools 158
- Disk Manager 166
- IP Address 167
- Configuring iSCSI Initiators 169
- Configuration Notes 171
- (Target Portal) 172
- Automatically restore 173
- Microsoft Windows 178
- Requirements 178
- 3 Click OK to save changes 183
- Using the CLI 185
- Access Levels and Passwords 186
- About Parameters 189
- About Manage Commands 189
- Command Abbreviation 189
- Command Completion 190
- Command Line Editing 191
- Viewing Long Reports 192
- Getting Help 193
- Your Snap Server 700i Series 195
- Product Descriptions 196
- Where to Buy tab 197
- Component Description 198
- Optional Expansion Arrays 199
- Componen 202
- Specifications 204
- SANbloc S50 Specifications 205
- Safety Precautions 206
- RAID Quick Reference 207
- Expanding Pool Capacity 208
- Completing a Silent Windows 209
- Installation 209
- Property Values 210
- MGMTPASS=pass” 213
- OS Support Quick Reference 215
- Supported iSCSI Initiators 216
- Windows OSs 216
- Windows Support Components 217
- OS with Latest Service 217
- Windows Server 2003: 217
- Glossary 219
- Term Definition 220
Verwandte Produkte und Handbücher für Server Adaptec Snap Server 700i Series
(8 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern