Adaptec SATA II RAID 1220SA Betriebsanweisung Seite 32
- Seite / 103
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 4: Installing the HostRAID Controller and Disk Drives l32
3 When all internal disk drives have been installed and connected, close your computer
cabinet, reconnect the power cord.
Installing the SAS HostRAID Controller to a SAS Expander
You can use a SAS expander to connect multiple disk drives to your SAS HostRAID controller
(or to multiple SAS HostRAID controllers). Commands can be sent down one link and data
returned on another in a separate connection to increase fault tolerance. Using a SAS expander
and dual-port SAS drives and SATA drives with 2-port adapters, you can design redundant
systems for maximum fault-tolerance.
To install the HostRAID controller to a SAS expander:
1 Using the appropriate cable, connect the SAS HostRAID controller to the expander’s PHY
connector.
2 Connect a cable from the expander’s PHY connector to a disk drive.
Connecting Disk Drives to SATA HostRAID Controllers
1 Install your SATA disk drives, following the instructions in your system’s documentation.
There are no jumpers or switches to set on the SATA controller or disk drives.
2 Connect each disk drive to a SATA port on the controller using a recommended SATA
cable. For cable information, see page 30.
3 When all disk drives have been installed and connected, close your computer cabinet, and
reconnect the power cord.
Checking Your Controller and Devices
Now that you have installed your controller and connected your disk drives, you can use the
ARC utility to check your controller and devices, as described below:
1 Turn on your computer.
2 When the Adaptec banner appears, press Ctrl+A to enter the Adaptec RAID Configuration
(ARC) utility.
3 If your drives have already been used in another system (even if not part of an array), select
Disk Utilities and format the drive. Otherwise, skip to Step 4.
Disk drives on
backplane
Controller connected
to backplane with
fan-out cable
- SAS and SATA 1
- HostRAID Controller 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Adaptec Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- 5 Getting Started 7
- 6 Creating a Bootable Array 7
- 9 Managing Your Storage Space 8
- 10 Solving Problems 8
- A Introduction to SAS 8
- BUnderstanding RAID 8
- C Using the ARC Utility 9
- F Safety Information 10
- G Technical Specifications 10
- Glossary 10
- About This Guide 11
- How to Find More Information 12
- In this chapter 14
- HostRAID Controller Features 15
- External SAS Connector 18
- Internal SAS Connector 18
- 3.3V PCI-X Connector 18
- Mounting bracket 18
- PCIe X1 connector 23
- External SATA connectors 23
- J1 LED Connector 23
- Kit Contents and System 24
- Requirements 24
- Kit Contents 25
- System Requirements 25
- Disk Drives 26
- Before You Begin 27
- Selecting Disk Drives 28
- Selecting SAS Cables 28
- SAS or SATA disk drives 29
- Selecting SATA Cables 30
- Connecting to a Backplane 31
- Disk drives on 32
- Controller connected 32
- Setting the Boot Controller 33
- Next Steps 34
- Getting Started 35
- Choosing a RAID Level 36
- Choosing Installation Options 36
- Basic Installation Steps 36
- Creating a Bootable Array 38
- Creating an Array 39
- Making Your Array Bootable 40
- Creating a Driver Disk 42
- Installing with Windows 42
- Installing with Red Hat Linux 43
- Installing with SUSE Linux 43
- Installing with NetWare 44
- Operating System 45
- Installing on Windows Vista 47
- Installing on NetWare 47
- Managing Your Storage Space 49
- About Adaptec Storage Manager 50
- About the ARC Utility 51
- Which Utility Should I Use? 51
- Solving Problems 52
- Troubleshooting Checklist 53
- Resetting the Controller 54
- Understanding RAID 56
- RAID Technology Overview 57
- RAID 0 (Non-RAID Arrays) 57
- RAID 1 Arrays 58
- RAID 10 Arrays 58
- Selecting the Best RAID Level 59
- Introduction to SAS 60
- What is SAS? 61
- What’s a Phy? 62
- What’s a SAS Port? 62
- What’s a SAS Address? 63
- What’s a SAS Connector? 63
- What do SAS Cables Look Like? 63
- Direct-Attach Connections 64
- Backplane Connections 64
- SAS Expander Connections 64
- SAS DomainSAS Domain 65
- Using the ARC Utility 67
- Running the ARC Utility 68
- Creating and Managing Arrays 68
- RAID Via 69
- When Appropriate 69
- Managing Arrays 70
- Adding/Deleting Hot Spares 71
- Using SerialSelect 72
- SerialSelect Options 73
- Using SATASelect 74
- SATASelect Options 75
- Locating Disk Drives 76
- Identifying Disk Drives 76
- Viewing the Event Log 77
- In this Appendix 78
- Compatibility Information 79
- Introduction 79
- Running the AFU 80
- A:\> AFU HELP 81
- A:\> AFU /? 81
- Connector Reference 86
- Aggregate LED signals only 87
- Pin Number Signal Description 89
- Safety Information 91
- Technical Specifications 92
- Environmental Specifications 93
- DC Power Requirements 93
- Current Requirements 93
- Glossary ● 96 95
- Glossary ● 97 96
- Glossary ● 98 97
- Glossary ● 99 98
- Glossary ● 100 99
- Index ● 95 101
- Index ● 96 102
- Milpitas, CA 95035 USA 103
- Adaptec, Inc 103
- 691 South Milpitas Boulevard 103
Verwandte Produkte und Handbücher für Schnittstellenkarten / Adapter Adaptec SATA II RAID 1220SA
(206 Seiten)
(30 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern