Adaptec SATA II RAID 1220SA Betriebsanweisung Seite 72
- Seite / 103
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendix C: Using the ARC Utility ● 73
Managing Bootable Arrays and Devices
Select the Manager Boot Unit option to add or remove a bootable array or single drive.
1 From the ACU menu, select Manage Boot Unit.
2 Use the up and down arrow keys to highlight the array or single drive you want to
designate as a bootable device, then select Insert>Enter.
Note:
Adaptec 1225SA controller does not support bootable devices.
Configuring Disk Drives
Caution:
● If the drive is used in an array, you may not be able to use the array again. Do not
configure a drive that is part of a boot array. To determine which drives are associated
with a particular array, see Viewing Array Properties on page 71.
● The partition table on the disk will be deleted when deleting a simple volume.
To configure drives:
Note:
Configuring disk drives makes a simple volume. A simple volume can be managed like
normal arrays by using the Manage Arrays option on your Main menu.
1
From the menu, select Configure Drives.
2 Use the up and down arrow keys to highlight the disk you wish to configure, then press
Insert.
3 Repeat the previous step, if you want to add another drive to be configured.
4 Press Enter.
5 Read the warning message and ensure that you have selected the correct disk drives to
configure. Type
Y
to continue.
ATAPI Support
The following devices are supported:
● The 1225SA and 1220SA supports detection of SATA ATAPI TAPE Drive and CDROM.
● The 1225SA and 1220SA supports booting from the ELTORITO bootable CD/DVD media.
If a bootable CD/DVD media is detected, that bootable media gets precedence in the booting
order.
Using SerialSelect
The SerialSelect utility allows you to change the BIOS and SAS HostRAID controller and device
settings without opening the computer cabinet.
For more information, see SerialSelect Options on page 74.
!
- SAS and SATA 1
- HostRAID Controller 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Adaptec Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- 5 Getting Started 7
- 6 Creating a Bootable Array 7
- 9 Managing Your Storage Space 8
- 10 Solving Problems 8
- A Introduction to SAS 8
- BUnderstanding RAID 8
- C Using the ARC Utility 9
- F Safety Information 10
- G Technical Specifications 10
- Glossary 10
- About This Guide 11
- How to Find More Information 12
- In this chapter 14
- HostRAID Controller Features 15
- External SAS Connector 18
- Internal SAS Connector 18
- 3.3V PCI-X Connector 18
- Mounting bracket 18
- PCIe X1 connector 23
- External SATA connectors 23
- J1 LED Connector 23
- Kit Contents and System 24
- Requirements 24
- Kit Contents 25
- System Requirements 25
- Disk Drives 26
- Before You Begin 27
- Selecting Disk Drives 28
- Selecting SAS Cables 28
- SAS or SATA disk drives 29
- Selecting SATA Cables 30
- Connecting to a Backplane 31
- Disk drives on 32
- Controller connected 32
- Setting the Boot Controller 33
- Next Steps 34
- Getting Started 35
- Choosing a RAID Level 36
- Choosing Installation Options 36
- Basic Installation Steps 36
- Creating a Bootable Array 38
- Creating an Array 39
- Making Your Array Bootable 40
- Creating a Driver Disk 42
- Installing with Windows 42
- Installing with Red Hat Linux 43
- Installing with SUSE Linux 43
- Installing with NetWare 44
- Operating System 45
- Installing on Windows Vista 47
- Installing on NetWare 47
- Managing Your Storage Space 49
- About Adaptec Storage Manager 50
- About the ARC Utility 51
- Which Utility Should I Use? 51
- Solving Problems 52
- Troubleshooting Checklist 53
- Resetting the Controller 54
- Understanding RAID 56
- RAID Technology Overview 57
- RAID 0 (Non-RAID Arrays) 57
- RAID 1 Arrays 58
- RAID 10 Arrays 58
- Selecting the Best RAID Level 59
- Introduction to SAS 60
- What is SAS? 61
- What’s a Phy? 62
- What’s a SAS Port? 62
- What’s a SAS Address? 63
- What’s a SAS Connector? 63
- What do SAS Cables Look Like? 63
- Direct-Attach Connections 64
- Backplane Connections 64
- SAS Expander Connections 64
- SAS DomainSAS Domain 65
- Using the ARC Utility 67
- Running the ARC Utility 68
- Creating and Managing Arrays 68
- RAID Via 69
- When Appropriate 69
- Managing Arrays 70
- Adding/Deleting Hot Spares 71
- Using SerialSelect 72
- SerialSelect Options 73
- Using SATASelect 74
- SATASelect Options 75
- Locating Disk Drives 76
- Identifying Disk Drives 76
- Viewing the Event Log 77
- In this Appendix 78
- Compatibility Information 79
- Introduction 79
- Running the AFU 80
- A:\> AFU HELP 81
- A:\> AFU /? 81
- Connector Reference 86
- Aggregate LED signals only 87
- Pin Number Signal Description 89
- Safety Information 91
- Technical Specifications 92
- Environmental Specifications 93
- DC Power Requirements 93
- Current Requirements 93
- Glossary ● 96 95
- Glossary ● 97 96
- Glossary ● 98 97
- Glossary ● 99 98
- Glossary ● 100 99
- Index ● 95 101
- Index ● 96 102
- Milpitas, CA 95035 USA 103
- Adaptec, Inc 103
- 691 South Milpitas Boulevard 103
Verwandte Produkte und Handbücher für Schnittstellenkarten / Adapter Adaptec SATA II RAID 1220SA
(206 Seiten)
(30 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.168 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern