Adaptec SATA II RAID 1220SA Betriebsanweisung Seite 74
- Seite / 103
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendix C: Using the ARC Utility ● 75
Using SATASelect
The SATASelect utility allows you to change the BIOS and SATA HostRAID controller and
device settings without opening the computer cabinet.
To access SATASelect:
1 Restart the computer, then press Ctrl+A when prompted to access the ARC utility.
2 If multiple HostRAID controllers are installed, select the HostRAID controller you want to
configure, then press Enter.
3 From the ARC menu, select SATASelect Utility.
4 To select a menu option, browse with the arrow keys to the option, then press Enter. In
some cases, selecting an option displays another menu. You can return to the previous
menu at any time by pressing Esc.
5 To restore the default SATASelect values, press F6 from within the SATA Driver and
Controller Configuration screen.
6 To exit SATA Select, press Esc until a message prompts you to exit (if you changed any
settings, you are prompted to save the changes before you exit).
7 At the prompt, select Ye s to exit, then press any key to restart the computer. Any changes
you made in SATASelect take effect after the computer restarts.
Physical Drives Display
during Post
Enabled
Disabled
When Enabled, connected physical devices are
displayed during system POST. Displaying the
devices adds a few seconds to the overall POST
time.
PHY Configuration
PHY Rate Auto, 1.5, 3.0
The data transfer rate between the
HostRAID
controller and devices. The default setting is
Automatic, which allows the SAS HostRAID
controller to adjust the speed as needed.
SAS Address 0-F Specifies the last digit of a 64-bit SAS address of
the
HostRAID controller, device, and each port
using a globally unique worldwide name (WWN)
identifier.
Controller Properties
PCI Slot: Bus:
Device:Function
None Displays the path of the storage devices in a Host
RAID controller.
Interrupt (IRQ) Channel None Displays interrupt
I/O Port Address None Displays I/O port address
Device ID None Displays device ID
Controller Serial
Number
None Displays controller serial number
Controller WWN None Displays the controller WWN
SerialSelect Options Available Settings Description
- SAS and SATA 1
- HostRAID Controller 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Adaptec Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- 5 Getting Started 7
- 6 Creating a Bootable Array 7
- 9 Managing Your Storage Space 8
- 10 Solving Problems 8
- A Introduction to SAS 8
- BUnderstanding RAID 8
- C Using the ARC Utility 9
- F Safety Information 10
- G Technical Specifications 10
- Glossary 10
- About This Guide 11
- How to Find More Information 12
- In this chapter 14
- HostRAID Controller Features 15
- External SAS Connector 18
- Internal SAS Connector 18
- 3.3V PCI-X Connector 18
- Mounting bracket 18
- PCIe X1 connector 23
- External SATA connectors 23
- J1 LED Connector 23
- Kit Contents and System 24
- Requirements 24
- Kit Contents 25
- System Requirements 25
- Disk Drives 26
- Before You Begin 27
- Selecting Disk Drives 28
- Selecting SAS Cables 28
- SAS or SATA disk drives 29
- Selecting SATA Cables 30
- Connecting to a Backplane 31
- Disk drives on 32
- Controller connected 32
- Setting the Boot Controller 33
- Next Steps 34
- Getting Started 35
- Choosing a RAID Level 36
- Choosing Installation Options 36
- Basic Installation Steps 36
- Creating a Bootable Array 38
- Creating an Array 39
- Making Your Array Bootable 40
- Creating a Driver Disk 42
- Installing with Windows 42
- Installing with Red Hat Linux 43
- Installing with SUSE Linux 43
- Installing with NetWare 44
- Operating System 45
- Installing on Windows Vista 47
- Installing on NetWare 47
- Managing Your Storage Space 49
- About Adaptec Storage Manager 50
- About the ARC Utility 51
- Which Utility Should I Use? 51
- Solving Problems 52
- Troubleshooting Checklist 53
- Resetting the Controller 54
- Understanding RAID 56
- RAID Technology Overview 57
- RAID 0 (Non-RAID Arrays) 57
- RAID 1 Arrays 58
- RAID 10 Arrays 58
- Selecting the Best RAID Level 59
- Introduction to SAS 60
- What is SAS? 61
- What’s a Phy? 62
- What’s a SAS Port? 62
- What’s a SAS Address? 63
- What’s a SAS Connector? 63
- What do SAS Cables Look Like? 63
- Direct-Attach Connections 64
- Backplane Connections 64
- SAS Expander Connections 64
- SAS DomainSAS Domain 65
- Using the ARC Utility 67
- Running the ARC Utility 68
- Creating and Managing Arrays 68
- RAID Via 69
- When Appropriate 69
- Managing Arrays 70
- Adding/Deleting Hot Spares 71
- Using SerialSelect 72
- SerialSelect Options 73
- Using SATASelect 74
- SATASelect Options 75
- Locating Disk Drives 76
- Identifying Disk Drives 76
- Viewing the Event Log 77
- In this Appendix 78
- Compatibility Information 79
- Introduction 79
- Running the AFU 80
- A:\> AFU HELP 81
- A:\> AFU /? 81
- Connector Reference 86
- Aggregate LED signals only 87
- Pin Number Signal Description 89
- Safety Information 91
- Technical Specifications 92
- Environmental Specifications 93
- DC Power Requirements 93
- Current Requirements 93
- Glossary ● 96 95
- Glossary ● 97 96
- Glossary ● 98 97
- Glossary ● 99 98
- Glossary ● 100 99
- Index ● 95 101
- Index ● 96 102
- Milpitas, CA 95035 USA 103
- Adaptec, Inc 103
- 691 South Milpitas Boulevard 103
Verwandte Produkte und Handbücher für Schnittstellenkarten / Adapter Adaptec SATA II RAID 1220SA
(206 Seiten)
(30 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern