Adaptec 2110S - SCSI RAID Controller Installationsanleitung Seite 100
- Seite / 106
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
C-4
Adaptec RAID Installation Guide
The Adaptec controller BIOS reports a drive as a disk instead of a drive.
This condition can occur if SMOR is used to disable Boot Enable. If
you require access to disk drives connected to the Adaptec controller
during the boot process, set Bootable Devices to Normal.
After updating the Adaptec controller firmware or BIOS and restarting, LEDs 1 and 5
or 2 and 5 flash once per second.
These patterns indicate that the controller startup code detected a
firmware checksum error or a flash error. Disable the firmware,
BIOS, and SMOR and then replace them using the flash Mode 0
procedure. For details, refer to Appendix D.
A firmware upgrade is unsuccessful, causing the controller to hang the system.
You can temporarily disable the firmware, BIOS, and SMOR and
then replace them using the flash Mode 0 procedure. For details,
refer to Appendix D.
After an upgrade of the controller BIOS only, pressing Ctrl+A at the system prompt
displays the message
Card not configurable.
Upgrade SMOR using the flash Mode 0 procedure. For details, refer
to Appendix D.
The floppy disk drive cannot be accessed after installing an Adaptec controller.
Use SMOR to enable the EBDA Relocation option. For details, refer
to Using SMOR on page 2-11.
COMBINED RAID IG.BOOK Page 4 Tuesday, September 25, 2001 5:46 PM
- Adaptec RAID 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Adaptec, Inc 3
- Canadian Compliance Statement 4
- Contents 5
- 3 Installing the Driver 6
- A Card and Module Diagrams 8
- B Controller LEDs 8
- C Troubleshooting 8
- E Specifications 8
- System Requirements 10
- Kit Contents 11
- About the Documentation 14
- Introduction 15
- Files and Folders 16
- Product Documentation on CD 16
- Errata and Release Notes 17
- Cache Memory Module 19
- Safety Information 22
- Installing Your Controller 24
- Configuring SCSI Devices 25
- LVD and SE Devices 26
- SCSI Cables 26
- SCSI Device IDs 26
- SCSI Termination 27
- Seating the Module 30
- Adaptec 3200S/3400S Only 30
- Installing the Controller 32
- Using SMOR 34
- Installing the Driver 36
- Windows 2000 37
- Windows NT 4.0 41
- Controller 42
- 5 Select Adaptec I 46
- 8 Start up the system 46
- Creating the Driver Disk 47
- C drive 48
- (OEM SR2 – Version 95B) 50
- Novell NetWare 54
- NetWare 4.11 Server 55
- NetWare 4.2 Server 57
- C drive named nwupdate 58
- NetWare 5 Server 60
- SCO UNIX 62
- Installing Storage 69
- Management Software 69
- Installation Prerequisites 71
- NetWare 4.11 and 4.2 72
- NetWare 5.x 74
- Red Hat Linux and FreeBSD 75
- Installing Storage Manager 76
- SCO UnixWare 7 78
- ■ K Desktop Environment (KDE) 79
- Card and Module Diagrams 80
- Adaptec ATA RAID 2400A 81
- Adaptec SCSI RAID 2000S 82
- Adaptec SCSI RAID 2005S 83
- Adaptec SCSI RAID 2100S 84
- Adaptec SCSI RAID 2110S 85
- Adaptec SCSI RAID 3200S 86
- Adaptec SCSI RAID 3400S 87
- Adaptec SCSI RAID 3210S/3410S 88
- Controller LEDs 92
- LED During Power-up 93
- LEDs During Controller Idle 93
- LEDs During Controller Active 93
- Cache Status LEDs 94
- SCSI Bus Status LEDs 95
- Troubleshooting 97
- Controller Reset Procedures 101
- NVRAM Reset 102
- Flash Mode 0 102
- Specifications 104
- RINTED IN SINGAPORE 106
Verwandte Produkte und Handbücher für Motherboards Adaptec 2110S - SCSI RAID Controller
Motherboards Adaptec 3940AUW Bedienungsanleitung
(128 Seiten)
(128 Seiten)
Motherboards Adaptec 1045 Betriebsanweisung
(69 Seiten)
(69 Seiten)
Motherboards Adaptec AHA-2742 Betriebsanweisung
(118 Seiten)
(118 Seiten)
Motherboards Adaptec AHA-1744 Installationsanleitung
(191 Seiten)
(191 Seiten)
Motherboards Adaptec AVA-2825 Betriebsanweisung
(110 Seiten)
(110 Seiten)
Motherboards Adaptec AHA-3940 Betriebsanweisung
(102 Seiten)
(102 Seiten)
Igenix Forni manuali utente
Partendo da I
Kommentare zu diesen Handbüchern