Adaptec SAS RAID Controllers Installationsanleitung Seite 68
- Seite / 148
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
54 Sun StorageTek SAS RAID HBA Installation Guide • March 2010
BIOS Utility Issues
This section contains the known issues related to the BIOS RAID Configuration
Utility:
■ “Creating an Array With the BIOS Utility Changes the BIOS Boot Order” on
page 54
■ “Hot-Plug Functionality Does Not Work in the BIOS Utility” on page 54
■ “Performance Issues” on page 54
Creating an Array With the BIOS Utility Changes
the BIOS Boot Order
Workaround: After creating the array, check the BIOS settings to verify the correct
boot order and make changes as necessary. For more information, see “Best Practices
For Controlling the Boot Order of Logical Drives” on page 87.
Hot-Plug Functionality Does Not Work in the
BIOS Utility
Workaround: Hot-plugging of enclosures is not supported in the BIOS RAID
Configuration utility. Hot-plugging of SAS/SATA hard disk drives (HDDs) is
supported only within hard disk enclosures and only under the conditions specified
in “Understanding Hot-Plug Limitations and Conditions Within the BIOS RAID
Configuration Utility” on page 66.
Performance Issues
This section contains the known performance issues:
■ “The System Freezes When a Sun Storage 32GB SLC SATA Solid State Drive (SSD)
is Configured In the HBA” on page 55
■ “Cannot Access the HBA From the GUI Nor Access a LUN From the Host” on
page 55
■ “Data Miscompare With 3.5" SAS Disks” on page 55
- Sun StorageTekSAS RAID HBA 1
- Contents 3
- ▼ To View the Event Log 78 8
- Contents ix 9
- Declaration of Conformity 115 10
- Index 131 10
- Before You Read This Document 11
- Related Documentation 12
- Training 13
- Documentation Comments 13
- HBA Overview 15
- HBA Features 16
- Component Layout 17
- Requirements 19
- System Interoperability 20
- Server Support 21
- Software Support 21
- Observing ESD and Handling 23
- Precautions 23
- Installation Task Map 26
- ■ ESD wrist strap 28
- SPARC System 30
- Installing the HBA 31
- Connecting Disk Drives 33
- Testing the HBA Installation 34
- No Logical Drives Found 38
- Next Steps 39
- Removing the Hardware 39
- ▼ To Remove the HBA 40
- Creating an Array 42
- Making the Array Bootable 45
- Setting the Boot HBA 45
- Install the Solaris OS 48
- ▼ To Create a Logical Drive 49
- # ./arcconf GETCONFIG 1 LD 51
- # devfsadm 51
- Array on an x64 System 53
- Preparing to Install an OS 54
- ■ “Next Steps” on page 47 59
- Installing the Solaris OS 60
- Operating System 63
- Linux OS 64
- Known Issues 67
- BIOS Utility Issues 68
- Performance Issues 68
- Chapter 8 Known Issues 55 69
- Configuration Rules 71
- ■ Maximum length of 1 meter 72
- HBA Specifications 73
- Environmental Specifications 74
- DC Power Requirements 74
- Current Requirements 74
- Performance Specifications 74
- Connector Pin Definitions 75
- SATA Pin-Out 76
- SATA Power Pin-Out 77
- Introduction to the BIOS RAID 80
- Configuration Utility 80
- Hot-Plug Addition Conditions 81
- Conditions 81
- ▼ To Start the ACU 84
- ■ Delete an array 85
- Settings 87
- General HBA Settings 88
- Select Utility 89
- Utilities 90
- ▼ To View the Event Log 92
- Troubleshooting 93
- Silencing the Alarm 94
- Appendix D Troubleshooting 81 95
- Best Practices 97
- Making New Connections 98
- Enclosures 99
- Failure Conditions 99
- Failures 100
- Discovering Drives 101
- Order of Logical Drives 101
- RAID Logical Devices 102
- Appendix E Best Practices 89 103
- Selecting the Best RAID Level 105
- Understanding Drive Segments 106
- Nonredundant Arrays (RAID 0) 106
- RAID 1 Arrays 107
- RAID 1 Enhanced Arrays 108
- RAID 10 Arrays 109
- RAID 5 Arrays 110
- RAID 5EE Arrays 111
- RAID 50 Arrays 112
- RAID 6 Arrays 114
- RAID 60 Arrays 115
- Migrating RAID Levels 116
- APPENDIX 117
- About SAS 118
- About Phys 119
- About SAS Ports 120
- About SAS Addresses 120
- About SAS Connectors 121
- About SAS Cables 121
- About SAS Connection Options 122
- SAS Expander Connections 123
- Declaration of Conformity 129
- Safety Precautions 131
- Battery Warning 132
- System Unit Cover 133
- Rack System Instructions 133
- Laser Compliance Notice 133
- CD and DVD Devices 133
- Mesures de sécurité 133
- Symboles 134
- Modification du matériel 134
- Conformité SELV 134
- Couvercle de l'unité 135
- Périphériques CD et DVD 135
- Vorschriften 136
- Anschluss des Netzkabels 137
- Warnung bezüglich Batterien 137
- Gehäuseabdeckung 137
- Anweisungen zur Rack-Montage 137
- Normativas de seguridad 138
- Class 1 Laser Product 140
- Luokan 1 Laserlaite 140
- Klasse 1 Laser Apparat 140
- Laser Klasse 1 140
- FCC Class B Notice 143
- GOST-R Certification Mark 144
- Index 133 147
Verwandte Produkte und Handbücher für Peripheriegeräte Adaptec SAS RAID Controllers
Peripheriegeräte Adaptec 4000SAS Betriebsanweisung
(134 Seiten)
(134 Seiten)
Peripheriegeräte Adaptec ICP9085LI Betriebsanweisung
(113 Seiten)
(113 Seiten)
Peripheriegeräte Adaptec 5405Z Betriebsanweisung
(136 Seiten)
(136 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.651 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern