Adaptec SAS RAID Controllers Installationsanleitung Seite 88
- Seite / 148
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
74 Sun StorageTek SAS RAID HBA Installation Guide • March 2010
▼ To Modify General HBA Settings With a -Select
Utility
Note – Default HBA settings are suitable for most computers. Do not change the
default settings.
● Select Controller Configuration from the main -Select utility menu and change
the settings listed in the following table.
Some options may not be available for the HBA.
Note – Default settings are shown in bold type.
TABLE C-1 General HBA Settings
Option Description
Drive’s Write Cache When enabled, write cache is enabled on the disk drive. When
disabled, write cache is not used on the disk drive. It is
recommended that you disable write cache on the disk drive.
Caution - When write cache is enabled, there is a slight possibility
of data loss or corruption during a power failure.
Runtime BIOS When enabled, the HBA BIOS allows the HBA to act as a bootable
device. Disabling the BIOS allows another HBA to act as a
bootable device.
Automatic Failover When enabled, the HBA automatically rebuilds an array when a
failed disk drive is replaced. When disabled, the array must be
rebuilt manually.
Array Background
Consistency Check
When enabled, the HBA constantly verifies a redundant array.
Note that there may be a significant performance reduction.
Default is disabled.
BBS Support When enabled in systems that support BBS, the HBA is presented
as a bootable device in the BIOS.
Array-based BBS
Support
When enabled in systems that support BBS, the HBA presents
attached bootable devices up to the BIOS for boot device selection.
This is relevant for logical arrays. Default is disabled.
Physical Drives
Display During
POST
When enabled, connected disk drives are displayed during system
Power On Self Test (POST). Displaying the disk drives adds a few
seconds to the overall POST time. Default is disabled.
CD-ROM Boot
Support
When enabled, the system can be booted from a bootable CD.
Note—CDs are not supported by current software.
- Sun StorageTekSAS RAID HBA 1
- Contents 3
- ▼ To View the Event Log 78 8
- Contents ix 9
- Declaration of Conformity 115 10
- Index 131 10
- Before You Read This Document 11
- Related Documentation 12
- Training 13
- Documentation Comments 13
- HBA Overview 15
- HBA Features 16
- Component Layout 17
- Requirements 19
- System Interoperability 20
- Server Support 21
- Software Support 21
- Observing ESD and Handling 23
- Precautions 23
- Installation Task Map 26
- ■ ESD wrist strap 28
- SPARC System 30
- Installing the HBA 31
- Connecting Disk Drives 33
- Testing the HBA Installation 34
- No Logical Drives Found 38
- Next Steps 39
- Removing the Hardware 39
- ▼ To Remove the HBA 40
- Creating an Array 42
- Making the Array Bootable 45
- Setting the Boot HBA 45
- Install the Solaris OS 48
- ▼ To Create a Logical Drive 49
- # ./arcconf GETCONFIG 1 LD 51
- # devfsadm 51
- Array on an x64 System 53
- Preparing to Install an OS 54
- ■ “Next Steps” on page 47 59
- Installing the Solaris OS 60
- Operating System 63
- Linux OS 64
- Known Issues 67
- BIOS Utility Issues 68
- Performance Issues 68
- Chapter 8 Known Issues 55 69
- Configuration Rules 71
- ■ Maximum length of 1 meter 72
- HBA Specifications 73
- Environmental Specifications 74
- DC Power Requirements 74
- Current Requirements 74
- Performance Specifications 74
- Connector Pin Definitions 75
- SATA Pin-Out 76
- SATA Power Pin-Out 77
- Introduction to the BIOS RAID 80
- Configuration Utility 80
- Hot-Plug Addition Conditions 81
- Conditions 81
- ▼ To Start the ACU 84
- ■ Delete an array 85
- Settings 87
- General HBA Settings 88
- Select Utility 89
- Utilities 90
- ▼ To View the Event Log 92
- Troubleshooting 93
- Silencing the Alarm 94
- Appendix D Troubleshooting 81 95
- Best Practices 97
- Making New Connections 98
- Enclosures 99
- Failure Conditions 99
- Failures 100
- Discovering Drives 101
- Order of Logical Drives 101
- RAID Logical Devices 102
- Appendix E Best Practices 89 103
- Selecting the Best RAID Level 105
- Understanding Drive Segments 106
- Nonredundant Arrays (RAID 0) 106
- RAID 1 Arrays 107
- RAID 1 Enhanced Arrays 108
- RAID 10 Arrays 109
- RAID 5 Arrays 110
- RAID 5EE Arrays 111
- RAID 50 Arrays 112
- RAID 6 Arrays 114
- RAID 60 Arrays 115
- Migrating RAID Levels 116
- APPENDIX 117
- About SAS 118
- About Phys 119
- About SAS Ports 120
- About SAS Addresses 120
- About SAS Connectors 121
- About SAS Cables 121
- About SAS Connection Options 122
- SAS Expander Connections 123
- Declaration of Conformity 129
- Safety Precautions 131
- Battery Warning 132
- System Unit Cover 133
- Rack System Instructions 133
- Laser Compliance Notice 133
- CD and DVD Devices 133
- Mesures de sécurité 133
- Symboles 134
- Modification du matériel 134
- Conformité SELV 134
- Couvercle de l'unité 135
- Périphériques CD et DVD 135
- Vorschriften 136
- Anschluss des Netzkabels 137
- Warnung bezüglich Batterien 137
- Gehäuseabdeckung 137
- Anweisungen zur Rack-Montage 137
- Normativas de seguridad 138
- Class 1 Laser Product 140
- Luokan 1 Laserlaite 140
- Klasse 1 Laser Apparat 140
- Laser Klasse 1 140
- FCC Class B Notice 143
- GOST-R Certification Mark 144
- Index 133 147
Verwandte Produkte und Handbücher für Peripheriegeräte Adaptec SAS RAID Controllers
Peripheriegeräte Adaptec 4000SAS Betriebsanweisung
(134 Seiten)
(134 Seiten)
Peripheriegeräte Adaptec ICP9085LI Betriebsanweisung
(113 Seiten)
(113 Seiten)
Peripheriegeräte Adaptec 5405Z Betriebsanweisung
(136 Seiten)
(136 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.206 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern